document number: 43004 revision 13-jun-02 www.vishay.com 68 sha v ishay tansitor for technical questions, contact tantalum@vishay .com subminiature, leaded solid tantalum capacitors polar or non-polar features subminiature package size and light weight cylindrical case with axial or radial leads ? to 35 vdc 0.22 f to 68 f operating temperature range : - 55 c to + 125 c high stability and reliability ? ested in accordance with mil-prf-49137 utilize high cv technology to extend the range of capacitance values in each size unique and comprehensive custom design capability applications hearing aids portable communications space/avionics laptop computers. electrical characteristics operating temperature range: - 55 c to + 125 c capacitance : measured at 120 hz and 25 c with a maximum of 2.2 vdc bias and 1.0 volt rms signal. capacitance tolerance : standard tolerance is 20% for ratings 0.1 f and above, and + 40, - 20% for ratings below 0.1 f. special tolerances are also available. dissipation factor : when measured simultaneously with capacitance, df shall not exceed the value shown in the ratings tables. dc leakage current (dcl max) : when measured with dc voltage applied through a 1,000 ? resistor for 5 minutes, dc leakage ( a) shall not exceed: at @ 25 c : leakage current shall not exceed the values listed in the standard ratings tables at @ 85 c: leakage current shall not exceed 10 times the values listed in the standard ratings tables at @ 125 c and 66% of rated voltage: leakage current shall not exceed 15 times the values listed in the standard ratings tables. operating voltage : full working voltage up to 85 c. from 85 c to 125 c working voltage derates linearly to 66% of the 85 c working voltage. ordering information c = polar n = nonpolar sha model 1.0 capacitance in f a* lead configuration a = axial r = radial c7 case code 35 dc voltage rating at + 85 c m capacitance tolerance e = +40, -20% m = 20% k = 10% j = 5% example of part number code: sha1.0-35c7am *to complete part number in rating tables, add a or r. change suffix if special capacitance tolerance is required. mechanical specifications solder coated nickel leads (type n32 per mil-std-1276) are standard on all case sizes. leads are weldable and/or solderable. special leads are available on request (e.g. bare nickle, gold plated nickle or ribbon leads). lead length is 1 1/2?[38.1 mm] minimum on nonpolar parts. on polar parts the negative lead is 1-1/4? [31.8mm] minimum and the positive lead is 1-1/2? [38.1mm] minimum.
www.vishay.com 69 sha v ishay tansitor document number: 43004 revision 13-jun-02 for technical questions, contact tantalum@vishay .com dimensions in inches [millimeters] polar style e tolerance dot radial d axial d d d l l (+) (+) (-) 3rd dot and polarity 2nd dot 1 st dot 1 st dot 2 nd dot t olerance dot case max max max e tol code l d e d c0 0.100 0.057 0.030 0.015 0.007 [2.54] [1.45] [0.76] [0.38] [0.18] c1 0.110 0.067 0.050 0.015 0.010 [2.80] [1.70] [1.27] [0.38] [0.25] c2 0.125 0.067 0.050 0.015 0.010 [3.18] [1.70] [1.27] [0.38] [0.25] c3 0.145 0.067 0.050 0.015 0.010 [3.68] [1.70] [1.27] [0.38] [0.25] c4 0.160 0.070 0.050 0.015 0.010 [4.06] [1.78] [1.27] [0.38] [0.25] c5 0.160 0.077 0.050 0.015 0.010 [4.06] [1.96] [1.27] [0.38] [0.25] c6 0.190 0.077 0.050 0.015 0.010 [4.83] [1.96] [1.27] [0.38] [0.25] c7 0.200 0.080 0.050 0.015 0.010 [5.08] [2.03] [1.27] [0.38] [0.25] c8 0.225 0.100 0.070 0.020 0.010 [5.72] [2.54] [1.78] [0.51] [0.25] c9 0.250 0.150 0.120 0.025 0.016 [6.35] [3.81] [3.05] [0.64] [0.41] case max max max max e tol code la lr w t e d n1 0.175 0.135 0.120 0.070 0.100 0.020 0.010 [4.45] [3.43] [3.05] [1.78] [2.54] [0.51] [0.25] n2 0.210 0.160 0.120 0.070 0.100 0.020 0.010 [5.33] [4.06] [3.05] [1.78] [2.54] [0.51] [0.25] n3 0.240 0.200 0.140 0.080 0.100 0.020 0.010 [6.10] [5.08] [3.56] [2.03] [2.54] [0.51] [0.25] n4 0.275 0.235 0.190 0.105 0.125 0.020 0.010 [6.99] [5.97] [4.83] [2.67] [3.18] [0.51] [0.25] n5 0.310 0.270 0.290 0.155 0.200 0.025 0.016 [7.87] [6.86] [7.37] [3.94] [5.08] [0.64] [0.41] axial radial t w d d e lr w t la tolerance dot 1st dot 3rd dot 1 st dot 3rd dot (+) (-) non polar style 2nd dot tolerance dot 2nd dot (-) subminiature, leaded solid tantalum capacitors polar or non-polar
document number: 43004 revision 13-jun-02 www.vishay.com 70 sha v ishay tansitor for technical questions, contact tantalum@vishay .com standard ratings - polar capacitors 2 wvdc @ + 85 c 3.3 10 0.5 c1 sha3.3-2c1*m 15 10 0.5 c5 sha15-2c5*m 22 10 1.0 c6 sha22-2c6*m 68 10 1.5 c8 sha68-2c8*m 3 wvdc @ + 85 c 2.2 10 0.5 c1 sha2.2-3c1*m 3.3 10 0.5 c2 sha3.3-3c2*m 4.7 10 0.5 c3 sha4.7-3c3*m 6.8 10 0.5 c4 sha6.8-3c4*m 10 10 0.5 c5 sha10-3c5*m 15 10 1.0 c6 sha15-3c6*m 22 10 1.0 c7 sha22-3c7*m 47 10 1.5 c8 sha47-3c8*m 68 10 5.0 c9 sha68-3c9*m 4 wvdc @ + 85 c 1.5 8 0.5 c1 sha1.5-4c1*m 2.2 8 0.5 c2 sha2.2-4c2*m 3.3 8 0.5 c3 sha3.3-4c3*m 4.7 8 0.5 c4 sha4.7-4c4*m 6.8 8 0.5 c5 sha6.8-4c5*m 10 8 1.0 c6 sha10-4c6*m 15 8 1.0 c7 sha15-4c7*m 33 8 1.5 c8 sha33-4c8*m 47 8 5.0 c9 sha47-4c9*m 6 wvdc @ + 85 c 1.0 6 0.5 c1 sha1.0-6c1*m 1.5 6 0.5 c2 sha1.5-6c2*m 2.2 6 0.5 c3 sha2.2-6c3*m 3.3 6 0.5 c4 sha3.3-6c4*m 4.7 6 0.5 c5 sha4.7-6c5*m 6.8 6 1.0 c6 sha6.8-6c6*m 10 6 1.0 c7 sha10-6c7*m 22 6 1.5 c8 sha22-6c8*m 33 6 5.0 c9 sha33-6c9*m 10 wvdc @ + 85 c 0.68 6 0.5 c1 sha.68-10c1*m 1.0 6 0.5 c2 sha1.0-10c2*m 1.5 6 0.5 c3 sha1.5-10c3*m 2.2 6 0.5 c4 sha2.2-10c4*m 3.3 6 0.5 c5 sha3.3-10c5*m 4.7 6 1.0 c6 sha4.7-10c6*m 6.8 6 1.0 c7 sha6.8-10c7*m 15 6 1.5 c8 sha15-10c8*m 22 8 5.0 c9 sha22-10c9*m *add a for axial, r for radial capacitance max max. dcl case part number ( f) df (%) @ + 25 c ( a) code subminiature, leaded solid tantalum capacitors polar or non-polar
www.vishay.com 71 sha v ishay tansitor document number: 43004 revision 13-jun-02 for technical questions, contact tantalum@vishay .com standard ratings - polar capacitors *add a for axial, r for radial capacitance max max. dcl case part number ( f) df (%) @ + 25 c ( f) code 15 wvdc @ + 85 c 0.47 6 0.5 c1 sha.47-15c1*m 0.68 6 0.5 c1 sha.68-15c1*m 1.0 6 0.5 c3 sha1.0-15c3*m 1.5 6 0.5 c4 sha1.5-15c4*m 2.2 6 0.5 c5 sha2.2-15c5*m 3.3 6 1.0 c6 sha3.3-15c6*m 4.7 6 1.0 c7 sha4.7-15c7*m 15 8 5.0 c9 sha15-15c9*m 20 wvdc @ + 85 c 0.33 6 0.5 c1 sha.33-20c1*m 0.47 6 0.5 c2 sha.47-20c2*m 0.68 6 0.5 c3 sha.68-20c3*m 1.0 6 0.5 c4 sha1.0-20c4*m 1.5 6 0.5 c5 sha1.5-20c5*m 2.2 6 1.0 c6 sha2.2-20c6*m 3.3 6 1.0 c7 sha3.3-20c7*m 10 8 5.0 c9 sha10-20c9*m 25 wvdc @ + 85 c 2.2 6 1.0 c7 sha2.2-25c7*m 3.3 6 1.5 c8 sha3.3-25c8*m 6.8 8 5.0 c9 sha6.8-25c9*m 35 wvdc @ + 85 c 0.22 6 0.5 c1 sha.22-35c1*m 0.33 6 0.5 c2 sha.33-35c2*m 0.47 6 0.5 c3 sha.47-35c3*m 0.68 6 0.5 c4 sha.68-35c4*m 1.0 6 0.5 c5 sha1.0-35c5*m 1.5 6 0.5 c6 sha1.5-35c6*m 1.5 6 1.0 c7 sha1.5-35c7*m 2.2 6 1.5 c8 sha2.2-35c8*m standard ratings - non-polar capacitors capacitance max max. dcl case part number ( f) df (%) @ + 25 c ( f) code 2 wvdc @ + 85 c 3.3 10 0.5 n2 sha3.3-2n2*m 6.8 10 0.5 n3 sha6.8-2n3*m 15 10 1.0 n4 sha15-2n4*m 47 10 2.5 n5 sha47-2n5*m 4 wvdc @ + 85 c 2.2 8 0.5 n2 sha2.2-4n2*m 4.7 8 0.5 n3 sha4.7-4n3*m 10 8 1.0 n4 sha10-4n4*m 33 8 2.5 n5 sha33-4n5*m * add a for axial, r for radial subminiature, leaded solid tantalum capacitors polar or non-polar
document number: 43004 revision 13-jun-02 www.vishay.com 72 sha v ishay tansitor for technical questions, contact tantalum@vishay .com marking sha capacitors case sizes n4 and n5 are print marked: - capacitance is in picofarads - 1st and 2nd digits are significant figures - 3rd digit indicates the number of zeros. all other case sizes are have color dot marking: capacitance color digit in picofarads, indicated by 3 dots. black 0 1st and 2nd dot give brown 1 the significant digits. red 2 3rd dot indicates the number orange 3 of zeros. yellow 4 color dot location is shown on green 5 the dimensional sketches. blue 6 black dot is omitted on black sleeve. violet 7 grey 8 white 9 e.g. yellow-violet-green = 4,700,000 pf = 4.7 f capacitance tolerance color tolerance is indicated by a dot on the gold 5% side of the case. silver 10% black dot is omitted. none 20% none + 40%/- 20% the positive lead is indicated by a color dot of red epoxy on the unit. radial lead style is marked with brown epoxy on the top. axial lead style is marked with brown epoxy on the cathode end. 6 wvdc @ + 85 c 1.5 6 0.5 n2 sha1.5-6n2*m 3.3 6 1.0 n3 sha3.3-6n3*m 6.8 6 1.0 n4 sha6.8-6n4*m 22 6 2.5 n5 sha22-6n5*m 10 wvdc @ + 85 c 1.0 6 0.5 n2 sha1.0-10n2*m 2.2 6 1.0 n3 sha2.2-10n3*m 4.7 6 1.5 n4 sha4.7-10n4*m 15 6 2.5 n5 sha15-10n5*m 15 wvdc @ + 85 c 0.68 6 0.5 n2 sha.68-15n2*m 1.5 6 1.0 n3 sha1.5-15n3*m 3.3 6 1.5 n4 sha3.3-15n4*m 10 6 2.5 n5 sha10-15n5*m 20 wvdc @ + 85 c 0.47 6 0.5 n2 sha.47-20n2*m 1.0 6 1.0 n3 sha1.0-20n3*m 2.2 6 1.5 n4 sha2.2-20n4*m 6.8 6 2.5 n5 sha6.8-20n5*m 35 wvdc @ + 85 c 0.33 6 0.5 n2 sha.33-35n2*m 0.68 6 1.0 n3 sha.68-35n3*m 1.5 6 1.5 n4 sha1.5-35n4*m standard ratings - non-polar capacitors capacitance max max. dcl case part number ( f) df (%) @ + 25 c ( f) code * add a for axial, r for radial subminiature, leaded solid tantalum capacitors polar or non-polar
www.vishay.com 73 sha v ishay tansitor document number: 43004 revision 13-jun-02 for technical questions, contact tantalum@vishay .com performance and reliability the capacitors are tested in accordance with mil-prf- 49137, with specific requirements as follows: t emperature stability : when tested per mil-prf-49137/ 6, capacitance shall be within +/-15% at -55 c and 85 c, and +/-10% at 25 c after exposure to temperature extremes. df shall be within 200% of initial limit at - 55 c, 150% of initial limit at 85 c, and meet the initial at 25 c. dcl shall be within 10 x initial limit at 85 c, and meet the initial limit at 25 c. moisture resistance : (per method 106 of mil-std-202) after 10 cycles of 24 hours at 25 c to 65 c and 80-98% rh; capacitance shall be within +/-15% of initial value, df within 1.5 x initial limit and leakage within 3 x initial limit. life : (per method 108 of mil-std-202) after 1,000 hours at 85 c and rated voltage; capacitance shall be within +/-10% of initial limit, df within initial limits, and leakage within 200% of initial limit. surge voltage : (per mil-prf-49317) after 1,000 cycles at 85 c and 1.3 x wvdc; capacitance shall be within +/-10% of initial limit, df and leakage within initial limits. resistance to soldering heat : (per method 210 0f mil- std-202, condition b) after immersion in 260 c molten solder to within a 1/4?of the body of the unit, there shall be no evidence of mechanical or electrical degradation. solderability : (per method 208 of mil-std-202) after dipping leads in 235 c molten solder to within .125?of the body of the unit, the solder shall cover 95% of the lead surface. t erminal strength : (per method 211 of mil-std-202) after the following test there shall be no loosening of the terminals or permanent damage to the terminals. test condition a: (pull test) 0.010?leads withstand 1 pound, 0.016?leads 2 pounds and 0.007?leads 1/2 pound. test condition c: (bend t est) all leads shall withstand 3-90 bends with a 1/2 pound applied force. 1.0 0.1 0.01 -40 -10 0 +85 +20 (mfd-wvdc) 1 f-20v 100 f-10v d.c. leakage current ( a) temperature c leakage current - temperature capacitance vs. temperature +10 + 5 0 - 5 -10 -40 -10 +25 +100 +85 (mfd-wvdc) specification specification 100 f -10v 1 h-20v 100 f -10v typic al change in cap acitance % temperature 0 c 100 500 1 2 5 10 20 50 100 500 1 2 5 10 hz khz frequency khz mhz impedance-ohms (mfd-wvdc) 0.047 f-20v 0.047 f-20v 0.047 f-35v 0.047 f-50v 0.047 f-35v 4.7 f-10v 4.7 f-20v 4.7 f-20v impedance vs. frequency 0.1 0.2 0.5 1.0 2.0 5.0 10 20 50 100 200 500 1k 2k 5k 10k subminiature, leaded solid tantalum capacitors polar or non-polar
document number: 91000 www.vishay.com revision: 18-jul-08 1 disclaimer legal disclaimer notice vishay all product specifications and data are subject to change without notice. vishay intertechnology, inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, ?vishay?), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. vishay disclaims any and all li ability arising out of the use or application of any product describ ed herein or of any information provided herein to the maximum extent permit ted by law. the product specifications do not expand or otherwise modify vishay?s terms and conditions of purcha se, including but not limited to the warranty expressed therein, which apply to these products. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of vishay. the products shown herein are not designed for use in medi cal, life-saving, or life-sustaining applications unless otherwise expressly indicated. customers using or selling vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify vishay for any damages arising or resulting from such use or sale. please contact authorized vishay personnel to obtain written terms and conditions regarding products designed for such applications. product names and markings noted herein may be trademarks of their respective owners.
|
